How To Repair Sprinkler Pipe

Download Article

Download Article

If at that place are areas of your backyard that wait more similar to a marsh than a backyard, yous may have cleaved sprinkler pipes. Fortunately, fixing the problem isn't too difficult if you don't mind getting muddied.

Steps

1. 1

   Ensure yous have all the required supplies. Nothing is worse than having to run to the hardware store in the middle of a project. Meet the list of things you need below.

2. 2

   Find the rupture. Unremarkably a soggy surface area of grass, but sometimes it is a geyser.

   Ad

3. 3

   Turn off the sprinklers, if y'all don't this could be a very hard task.

4. iv

   Dig up the pipage. Not the whole piping, merely the section that is cleaved. Advisedly remove the department of grass above the pipe, trying to keep it intact. Do this by cut a circular department with the end of your shovel above where you are to dig and then carefully lifting it off. Dig up the dirt to a higher place the bad piping with a shovel (y'all volition probably also need a mitt trowel to dig up the dirt under the pipe). You will want to have at to the lowest degree six inches (xv.2 cm) on each side of the pause clear and enough room for you lot fist underneath the pipe. If the pigsty fills with water, you will either accept to wait for it to dry or bail it out (the latter is recommended).

5. v

   Cut the pipe. Get a hacksaw, PVC or metal pipe cutters (depending on what type of piping y'all have, older sprinkler systems are commonly metal, while newer ones tend to be PVC). Cut the broken section out and so that you have clean, undamaged pipe on both sides.

6. half-dozen

   Mensurate a new length of piping that is just a bit shorter than the gap left by onetime pipe that you lot cut away. It should probably be i/2 " to 1" shorter to permit room for the connectors. Or you can purchase a PVC fitting from near habitation improvement stores that has one pipe sliding inside an outer butt with an O-ring inside. It will extend almost 3" in length. You may run into in stores 1/two" to ii ane/ii" in diameter sizes. One end is a female person slip and the other is a male that needs a coupling, elbow, or tee to connect to consummate the repair.

7. 7

   Clean the pipe. Some water volition come up pouring out at first, you could try to catch it, simply it is easier to bail it out. Once the water stops coming out, clean both ends with a rag.

8. eight

   Fit the new section. If you lot are lucky enough to have PVC then you lot just put the PVC primer and mucilage on the outside of the pipage and within of the straight connectors and slip them together. Piece of work quickly considering the gum sets fast. Then put the section you just glued in the gap y'all just created, repeating the gluing procedure. If yous have metallic pipes yous will have to thread the exterior of the pipe to fit the connectors rather than gluing them.

9. 9

   Test the pipe. Turn the sprinklers dorsum on and make sure it is sealed properly.

10. x

    If everything is fixed, comprehend upwardly the hole and replace the grass you so carefully removed before.

Advertisement

Ask a Question

200 characters left

Include your electronic mail accost to get a message when this question is answered.

Submit

Advertizing

Thank you for submitting a tip for review!

• Be careful when digging, y'all never know what you might hit with your shovel.

Advertisement

Things You lot'll Need

• Shovel & trowel
• Piping
• two straight connectors
• hacksaw or pipe cutter
• for PVC, glue and primer
• for metal, a threader
• Rags
• 2 Hours

Nearly This Article

Thank you to all authors for creating a page that has been read 53,527 times.

Did this article assistance you?

Source: https://www.wikihow.com/Fix-a-Broken-Sprinkler-Pipe

Share this post